Rollingwood, CA— fire, flood & earthquake hazard information
Rollingwood is a unincorporated community in Contra Costa County in the San Francisco Bay Area, covering about 0.2 square miles. This page summarizes what official government maps show for Rollingwood: CAL FIRE fire hazard severity zones, FEMA flood zones, state seismic hazard zones, dam inundation areas, airport noise contours, and air-quality indicators. Figures are the share of Rollingwood’s area that falls inside each mapped zone.
View Rollingwood on the interactive map → to check any specific address, free.
Wildfire hazard severity zones
CAL FIRE's current Fire Hazard Severity Zone maps do not designate any zones within Rollingwood. Individual properties near the boundary can still fall inside a neighboring zone — check the exact address on the map.
FEMA flood zones
FEMA's National Flood Hazard Layer does not map any Special Flood Hazard Areas within Rollingwood. Unmapped does not mean flooding cannot occur — it means no zone is currently designated.
Earthquake faults & seismic zones
The nearest mapped fault, the Hayward fault zone, is about 0.1 mi (0.2 km) from the center of Rollingwood. 1 named fault trace in the USGS Quaternary fault database cross its boundary. 97% of its area is in a state-designated liquefaction zone of required investigation. less than 1% is in an earthquake-induced landslide zone. 43% falls within an Alquist-Priolo earthquake fault zone, where new construction requires a fault study.
| Nearest mapped fault | Hayward fault zone — 0.1 mi (0.2 km) |
| Named fault traces crossing boundary | 1 |
| Liquefaction zone | 97% |
| Earthquake-induced landslide zone | less than 1% |
| Alquist-Priolo fault zone | 43% |
Dam inundation, aircraft noise & air quality
100% of Rollingwood lies within a state-reviewed dam-failure inundation area; annual average fine-particle (PM2.5) concentration across its census tracts is 9.1 μg/m³, and its composite pollution burden ranks around the 42th percentile statewide.
| Dam-failure inundation area | 100% |
| Annual PM2.5 (tract average) | 9.1 μg/m³ |
| Pollution burden percentile (statewide) | ~42 |
Frequently asked questions
- Is Rollingwood in a wildfire hazard severity zone?
- CAL FIRE's current Fire Hazard Severity Zone maps do not designate any zones within Rollingwood. Individual properties near the boundary can still fall inside a neighboring zone — check the exact address on the map.
- Is Rollingwood in a FEMA flood zone?
- FEMA's National Flood Hazard Layer does not map any Special Flood Hazard Areas within Rollingwood. Unmapped does not mean flooding cannot occur — it means no zone is currently designated.
- What earthquake faults and seismic zones affect Rollingwood?
- The nearest mapped fault, the Hayward fault zone, is about 0.1 mi (0.2 km) from the center of Rollingwood. 1 named fault trace in the USGS Quaternary fault database cross its boundary. 97% of its area is in a state-designated liquefaction zone of required investigation. less than 1% is in an earthquake-induced landslide zone. 43% falls within an Alquist-Priolo earthquake fault zone, where new construction requires a fault study.
- How do I check a specific address in Rollingwood?
- Use the free sitelume interactive map at https://sitelume.com — search any Rollingwood address to see which mapped zones it falls in, layer by layer.
Nearby in Contra Costa County
Sources: CAL FIRE Fire Hazard Severity Zones; FEMA National Flood Hazard Layer; USGS Quaternary Faults; CGS Seismic Hazard Zones & Alquist-Priolo zones; Cal OES dam inundation maps; county ALUC noise contours; CalEnviroScreen 4.0. Area shares are computed against each place’s Census TIGER boundary (last computed 2026-07-24). Boundaries and zone designations change; always verify with the issuing agency.